Seshu Kumar, G. S. V., Anshuman, Kumar, Rajesh, S, Raju Chekuri, Rama Bhadri, Ramakotaiah, K.. (1400). Optimization of FSW process parameters for welding dissimilar 6061 and 7075 Al alloys using Taguchi design approach. هنرهای کاربردی, 13(1), 1011-1022. doi: 10.22075/ijnaa.2021.24678.2795
G. S. V. Seshu Kumar; Kumar Anshuman; S Rajesh; Rama Bhadri Raju Chekuri; K. Ramakotaiah. "Optimization of FSW process parameters for welding dissimilar 6061 and 7075 Al alloys using Taguchi design approach". هنرهای کاربردی, 13, 1, 1400, 1011-1022. doi: 10.22075/ijnaa.2021.24678.2795
Seshu Kumar, G. S. V., Anshuman, Kumar, Rajesh, S, Raju Chekuri, Rama Bhadri, Ramakotaiah, K.. (1400). 'Optimization of FSW process parameters for welding dissimilar 6061 and 7075 Al alloys using Taguchi design approach', هنرهای کاربردی, 13(1), pp. 1011-1022. doi: 10.22075/ijnaa.2021.24678.2795
Seshu Kumar, G. S. V., Anshuman, Kumar, Rajesh, S, Raju Chekuri, Rama Bhadri, Ramakotaiah, K.. Optimization of FSW process parameters for welding dissimilar 6061 and 7075 Al alloys using Taguchi design approach. هنرهای کاربردی, 1400; 13(1): 1011-1022. doi: 10.22075/ijnaa.2021.24678.2795

Optimization of FSW process parameters for welding dissimilar 6061 and 7075 Al alloys using Taguchi design approach

International Journal of Nonlinear Analysis and Applications
مقاله 84، دوره 13، شماره 1، خرداد 2022، صفحه 1011-1022    اصل مقاله (803.69 K)
نوع مقاله: Research Paper
شناسه دیجیتال (DOI): 10.22075/ijnaa.2021.24678.2795
نویسندگان
G. S. V. Seshu Kumar* 1؛ Kumar Anshuman1؛ S Rajesh2؛ Rama Bhadri Raju Chekuri2؛ K. Ramakotaiah3
1Department of Mechanical Engineering, Koneru Lakshmaiah Education Foundation (Deemed to be University), Vaddeswaram, Andhra Pradesh, India
2Department of Mechanical Engineering, Sagi Rama Krishnam Raju Engineering College, Bhimavaram, Andhra Pradesh, India
3Department of Mechanical Engineering, KKR and KSR Institute of Technology and Sciences, Guntur, Andhra Pradesh, India
چکیده
Friction stir welding (FSW) produce a strong metallurgical joint with the application of severe deformations and frictional heating in the metals and alloys by using a non-consumable rotating tool consisting of pin and tool shoulder. During welding, the plastic deformations of base metals vary for the varying mechanical properties such as tensile strength (TS), impact strength (IS), and hardness (HV) which in turn varies the welding conditions and parameters. Therefore, selection of optimal weld parameters plays an important role in enhancing the quality of weld joint. In this article, friction stir butt welds made of 6061 and 7075 Al alloys are performed with various welding parameters such as rotational speed of tool, angle of tilt, and axial force using tool has taper pin profile. Experiments are carried out on twenty-seven joints that are made on 6061 and 7075 Al Alloy plates of 6.50 mm thick of same nature and tested for its tensile, impact and HV properties.
کلیدواژه‌ها
Friction stir welding؛ 6061 and 7075 Al alloys؛ Taguchi design approach
مراجع
آمار
تعداد مشاهده مقاله: 16,849
تعداد دریافت فایل اصل مقاله: 10,442
دانشگاه سمنان
پیوندهای مفید
آمار
تعداد نشریات22
تعداد شماره‌ها725
تعداد مقالات10,482
تعداد مشاهده مقاله73,453,805
تعداد دریافت فایل اصل مقاله64,857,078